Categories
Blog

How to Choose a Commercial Kitchen Exhaust Hood for a Small Cafe

The right exhaust hood removes heat, grease and odors so your small kitchen stays safe and comfortable. You have four decisions to make, and each one depends on your menu, space and budget. Here are the worked examples for a typical 30-seat cafe.

Do I need a Type I or Type II exhaust hood?

A Type I hood removes grease, smoke and heat produced by cooking with oils or solid fuels. It includes a fire suppression system and grease filters, and it connects to a duct that vents outside. A Type II hood handles only steam, heat and odors, with no grease removal or fire suppression. It is used over equipment that does not produce airborne grease.

If your cafe fries, grills, sautés or cooks with any kind of oil, you need a Type I hood. A Type II hood suits ovens used only for baking bread or pastries, dishwashers and steamers. A cafe that roasts vegetables with olive oil on a flat top still requires Type I because the oil aerosolizes. A bagel shop that only boils and bakes can use Type II over the kettle and oven.

If you install the wrong type, you will fail a fire inspection and may void your insurance. Local mechanical codes classify every cooking appliance by the effluent it produces, and the hood type must match. When in doubt, assume Type I. A Type I system costs more because of the fire suppression, welded ductwork and makeup air, but you cannot skip it if you cook with fat.

How do I calculate the right CFM for my kitchen?

CFM, or cubic feet per minute, measures the volume of air the exhaust fan moves. The base formula multiplies the hood's open area by a capture velocity that depends on the cooking style. For a wall-mounted hood over a standard hot line, 100 feet per minute is the accepted minimum to pull grease and heat away from the cook.

The calculation is hood width × hood depth × capture velocity × a safety factor of 1.1. A 6-foot hood that extends 4 feet over the equipment covers 24 square feet. Multiply by 100 fpm and then by 1.1, and you get 2,640 CFM. That figure covers the exhaust only. You also need makeup air, which replaces the air you pull out and prevents backdrafting from flues or pressure problems in the dining room.

  • Measure the actual canopy area, not the cooking surface underneath.
  • Add 10 percent if you run a charbroiler or wok station.
  • Check local mechanical code for minimum makeup air ratios, often 80 percent of exhaust.
  • Confirm the fan can deliver the rated CFM against the static pressure of your duct run.
  • An oversized hood wastes energy and chills the kitchen in winter by pulling in too much cold makeup air.

Baffle, cartridge or mesh filters: which one suits a small cafe?

A small cafe frying bacon, searing burgers or grilling chicken needs a filter that captures grease without choking airflow. Baffle filters do exactly that. They consist of overlapping stainless steel vanes that force the airstream into tight turns. Grease droplets hit the metal and drain into a trough, while air passes through with little resistance.

Mesh filters are the budget option found in light-duty residential and recirculating hoods, but they fail the main test for a commercial kitchen. The fine aluminium layers trap grease quickly, clog within a shift and raise the pressure drop until the fan cannot pull enough air. Most building codes, including NFPA 96, classify them as unsuitable for grease-producing cooking, so an inspector will flag them straight away.

Cartridge filters sit between the two. They use a perforated metal box with an internal baffle path, giving higher grease removal than a standard baffle at a higher purchase cost. For a small cafe the practical default is a stainless steel baffle filter, 304 grade, sized to match the hood slot. The three types compare as follows:

  • Baffle filters remove roughly 80 to 95 percent of airborne grease depending on face velocity and are accepted by all commercial codes.
  • Mesh filters start with moderate capture but clog fast, which raises static pressure and kills extraction volume within a single service.
  • Cartridge filters reach up to 98 percent grease removal and suit heavy charbroiling or wok lines, though the price is roughly double a standard baffle.
  • Cleaning a baffle takes a dishwasher cycle or a soak in a degreaser tank, while a clogged mesh filter often needs replacement because the layers trap carbonised fat permanently.
  • Pressure drop across a clean baffle is the lowest of the three types, so the exhaust fan works less and the cafe saves on energy over the year.

What noise level should I expect and how do I reduce it?

A small cafe exhaust hood running at full speed typically produces 65 to 75 dBA at the hood face. For comparison, normal conversation sits around 60 dBA. You hear noise from three main sources: the fan itself, air rushing through the ductwork, and the makeup air system dumping unconditioned air into the kitchen. A well-designed system keeps hood noise below 70 dBA at the cook’s position.

Fan blade design makes a measurable difference. Forward-curved centrifugal fans are cheaper and common in packaged hood units, but they generate more turbulence and a higher-pitched whine. A backward-inclined centrifugal fan moves the same air volume with less blade tip turbulence and typically runs 4-6 dBA quieter. If the fan mounts on the roof rather than inside the hood, the noise at the cooking line drops further because the motor and impeller sit outside the building envelope.

Duct velocity and makeup air placement affect what your customers hear in the dining area. Commercial codes require duct velocities between 1,500 and 2,500 fpm; running at the low end of that range reduces duct rumble. Position the makeup air diffuser away from the dining room entrance and use a perforated diffuser plate rather than an open grille. The diffuser slows incoming air and cuts the low-frequency throb that travels through open doorways.

  • Select a hood with a backward-inclined fan or specify an external roof-mounted fan to move motor noise outside.
  • Size the ductwork for 1,500 fpm velocity, not the maximum allowed, to reduce air rush and vibration.
  • Place the makeup air supply at least 10 feet from the dining area opening and use a perforated diffuser face.
  • Mount the hood on vibration isolation brackets and install a flexible duct collar between the hood and the rigid duct riser.
  • Run the exhaust fan through a variable speed controller and dial it down during off-peak hours when full capture is not needed.

Wall-mounted, island or under-cabinet: which hood configuration works?

Wall-mounted hoods bolt directly to the wall behind the cooking line and vent out the back or through the roof. They suit most small cafes because the wall provides natural support and a short, straight duct run, which keeps installation simpler and extraction more efficient.

Island hoods hang from the ceiling over a cooking block that sits in the open, away from any wall. They need a stronger support frame, longer ductwork across the ceiling, and roughly 20-30% higher CFM to capture the same amount of smoke and grease, since no wall helps contain the rising plume. The extra steelwork, fire suppression piping and make-up air routing push the installed cost well above a comparable wall unit.

Under-cabinet hoods tuck beneath a shelf or pass-through and work only with light-duty electric equipment, such as a single countertop griddle or panini press. Their limited capture area and lower airflow make them unsuitable for a primary cooking battery that includes a fryer or charbroiler.

  • Wall-mounted units use the wall as a natural barrier and need the shortest duct path.
  • Island hoods demand higher CFM, ceiling reinforcement and longer duct runs.
  • An island hood typically costs two to three times as much to install as a wall-mounted unit of the same length.
  • Under-cabinet hoods suit only light electric appliances with low grease output.
  • A wall-mounted hood lets you add side panels later to improve capture without changing the main unit.
  • If your range sits on an island, plan for a dedicated make-up air system, because the hood cannot borrow wall-adjacent supply grilles.

What fire suppression and code requirements apply to a cafe hood?

A Type I hood over cooking equipment that produces grease-laden vapors requires a UL 300 listed automatic fire suppression system. This system discharges wet chemical agent directly onto the cooking surface, into the plenum and through the exhaust duct when a fusible link in the hood canopy melts at a preset temperature. The same activation automatically shuts off the gas or electric supply to the appliances under the hood.

NFPA 96 sets the minimum clearance from the hood and duct to combustible materials at 18 inches, though double-wall duct with a ventilated chase can reduce that to 6 inches. A dedicated makeup air system linked to the exhaust fan prevents backdrafting of combustion gases from other equipment. The local fire marshal inspects the installation before you open and during annual inspections afterward. No equipment supplier can certify your setup. Only a licensed fire suppression contractor can install, tag and service the system, and only the authority having jurisdiction signs off on the final clearance.

How do I keep the hood clean and pass a health inspection?

Wipe down all exterior stainless steel surfaces daily with a warm degreaser solution to stop sticky residue from hardening. Baffle filters slide out without tools and can be run through a commercial dishwasher each night, which removes the bulk of trapped grease before it restricts airflow.

The hood interior and plenum need a weekly manual scrub using a non-abrasive pad and food-safe degreaser. Pay attention to the drain trough and grease cup, empty the cup before it reaches three-quarters full to avoid an overflow that an inspector will flag immediately.

Professional duct cleaning intervals follow NFPA 96 guidelines based on cooking volume and fuel type:

  • Monthly cleaning for solid fuel operations such as wood-fired or charcoal cooking.
  • Quarterly cleaning for high-volume kitchens using fryers, woks or charbroilers.
  • Semi-annual cleaning for moderate-volume restaurants with standard griddles and ranges.
  • Annual cleaning for low-volume cooking such as soup and sandwich prep with no open flame.

Keep a dated log of every cleaning: filter runs, weekly scrubs and duct service visits. An inspector will ask for written records before climbing a ladder. A complete log turns a five-minute check into a pass.

FAQ

Can I install a residential range hood in a small cafe?

No. Residential hoods lack the fire suppression, grease containment and airflow capacity required by commercial building codes. An inspector will flag it, and your insurance will not cover a fire that starts at an unlisted appliance. You need a UL-listed Type I or Type II hood installed by a licensed contractor.

How much makeup air does a cafe exhaust hood need?

Makeup air must replace about 80 to 90 percent of the air the hood exhausts, or the kitchen will pull air from the dining room and struggle to maintain temperature. A 2,000 CFM hood typically needs 1,600 to 1,800 CFM of conditioned makeup air delivered near the hood, not dumped directly into the plume.

Do I need a separate exhaust hood for the dishwasher?

A high-temperature dishwasher producing steam and heat needs a Type II hood or a dedicated condensate hood. Some undercounter models with a built-in condenser may not require one, but a ventless dishwasher in a small cafe still adds humidity. Check the manufacturer's installation manual and your local mechanical code.

What is the typical cost of a commercial exhaust hood for a small cafe?

The cost depends on hood size, filter type, fire suppression and installation complexity. A basic 6-foot wall-mounted Type I hood with baffle filters costs less than an island hood of the same length, and the ductwork, makeup air unit and electrical work often exceed the hood price itself. Get three quotes from licensed kitchen exhaust contractors to compare the full installed cost.

By Emma Brown

Discover expert advice, industry trends, and practical tips on commercial kitchen equipment from Emma Brown. Stay informed with in-depth articles and professional insights.

Leave a Reply

Your email address will not be published. Required fields are marked *

Latest posts